Project Summary
NovaPeak deployed its thermal drone capability to support inspection works at Jewel, Singapore, combining aerial visual assessment with thermal imaging as part of a broader building-condition investigation.
This engagement is significant because it demonstrates that drones are not limited to Periodic Façade Inspection (PFI). In this case, drone deployment supported Periodic Structural Inspection (PSI) objectives as well as the investigation of water ingress and leak-related conditions.
For a large and architecturally complex development, conventional inspection methods alone can be time-consuming, disruptive or limited by accessibility. By deploying drones equipped with thermal sensing, NovaPeak was able to capture condition information from elevated and difficult-to-access areas while supporting the wider engineering assessment with visual and temperature-based evidence.
The Challenge
Large mixed-use developments often contain complex roof forms, elevated structures, concealed drainage paths and difficult-access building interfaces.
When water ingress or leakage is suspected, the visible symptoms observed inside the building may be far removed from the original entry point. Likewise, structural inspection of elevated elements can be constrained by access limitations, safety requirements and the need to minimise operational disruption.
This project therefore required more than a routine inspection.
The challenge was twofold:
first, to support PSI-related visual assessment of difficult-access building elements; and second, to investigate whether thermal imaging could help identify areas associated with moisture ingress, trapped water or abnormal thermal behaviour that warranted further attention.
In other words, the inspection needed to move beyond “looking at the building” and toward diagnosing what might be happening within or around it.
Why This Case Study Matters
This project is important because it illustrates a capability that is often overlooked in the market.
Drones are commonly associated with PFI and external façade reviews. However, NovaPeak’s work at Jewel demonstrates that drone platforms can also support PSI workflows and wider building-diagnostic investigations.
That distinction is valuable.
It positions NovaPeak not merely as a drone operator, but as a company that applies drone technology within broader engineering inspection and diagnostic methodologies.
NovaPeak’s Approach
NovaPeak approached the assignment as a combined inspection and diagnostic exercise.
The first step was to establish the relevant inspection areas, likely paths of access limitation and the parts of the building that could benefit most from aerial observation. This allowed the field team to identify where drone-based visual capture and thermal imaging would add value relative to conventional inspection methods.
Using a thermal drone, NovaPeak carried out aerial data capture of the relevant building areas, gathering both visual imagery and thermal information. The visual data supported close observation of the building condition, while the thermal data helped highlight temperature anomalies that could be associated with moisture presence, water pathways, localised saturation, concealed leakage or other hidden irregularities.
These datasets were then considered together.
Thermal results were not treated as a diagnosis on their own. Instead, they were used as an additional layer of evidence to support engineering interpretation. Areas exhibiting unusual thermal signatures could then be correlated against visible defects, known leakage concerns, structural locations or other site observations.
This is an important principle in NovaPeak’s methodology:
thermal imaging is a diagnostic aid, not a shortcut to conclusions.
Supporting PSI with Drone Technology
One of the most valuable aspects of this engagement is that it demonstrates how drones can support Periodic Structural Inspection in addition to façade-related inspection work.
For large and architecturally complex buildings, elevated structural and building elements may be difficult to view properly from the ground. Drone deployment can provide closer visual access to these areas, allowing the inspection team to capture a more complete condition record without immediately relying on more intrusive access arrangements.
In this project, the drone served as a tool for safe visual access, structured data capture and targeted diagnostic review.
That is a different proposition from using drones only for regulatory façade compliance.
It shows how NovaPeak can adapt drone workflows to support broader structural inspection objectives.
The Role of Thermal Imaging in Leak Investigation
Water ingress investigations are often challenging because the visible manifestation of a leak is not always located at the actual point of water entry.
Water may travel along concealed routes, accumulate behind finishes or appear only after spreading through multiple building interfaces.
Thermal imaging helps by revealing temperature contrasts that may indicate moisture retention, evaporative cooling, wet materials or abnormal thermal behaviour. When interpreted carefully, these signatures can help narrow down areas of concern and support more focused follow-up inspection or rectification.
For NovaPeak, the real value lies in combining this thermal layer with other information:
- visual condition of the building element
- known leakage complaints or observed symptoms
- geometry and likely water paths
- accessibility of the inspection zone, and
- engineering judgement on what the anomaly may mean.
This turns thermal drone work from a simple imaging exercise into a more complete building diagnostic process.
From Inspection Data to Engineering Evidence
The strength of the Jewel case study lies in how multiple evidence streams can be combined.
Rather than treating drone images, thermal captures and site observations as separate deliverables, NovaPeak’s value comes from integrating them into one inspection narrative.
That process can be understood as:
This evidence chain is what gives the inspection practical value for owners, facility managers, consultants and engineers.
Without that integration, thermal imagery is just a colourful picture.
With proper engineering context, it becomes part of a structured decision-making process.
What the Case Demonstrates
This project demonstrates several important NovaPeak capabilities at once.
It shows NovaPeak’s ability to deploy thermal drones for leak investigation, to support PSI-related inspection activities using drones, to inspect difficult-access building areas more safely and efficiently, and to convert drone-captured data into a form that supports practical engineering understanding.
Just as importantly, it shows that NovaPeak can apply drones in a problem-solving role, not only in a compliance or imaging role.
That is the strategic difference.
The Outcome
The Jewel inspection demonstrated that drone-based thermal and visual assessment can add meaningful value to large-building inspections where access, safety and diagnostic complexity are all relevant.
By combining aerial access with thermal sensing, NovaPeak was able to support the inspection process with richer condition data, assist in the investigation of possible water ingress pathways and expand the role of drone technology beyond conventional façade inspection.
For building owners and engineering teams, this means faster access to difficult areas, better visibility of suspected problem zones and a stronger evidence base for maintenance, rectification or further engineering assessment.